PSG Group InternationalPSG Group International
A fan of material samples in different colours and finishes

Tools

Material finder.

Find the right material for a gasket, seal, shim or electrical insulator. Tell us the temperature, what the part meets and what else it must do, and the finder ranks our materials with the reasons for and against each.

Materials compared
35
Media rated for chemical resistance
8

Material finder

Answer in any order.

Choose what you are making, then answer as many of the questions as you like. Every answer reorders the list, and you can share or copy the result.

Start from a common job, or answer below

Working temperature

The lowest and highest the part will see. Leave either as Any.

What will it meet?

Choose all that apply. Ratings are at room temperature.

How much pressure?

The duty decides how hard the gasket must be.

Anything else?

Choose any that apply.

Every material for this job

13 materials fit

Answer any question, or pick a common job, and the list ranks itself as you go.

Typical values from our material guides, for comparing materials: not a specification. Tell us the duty and our technical team will confirm the grade. Compare every material side by side in our gasket material chart.

How it decides

The rules behind the ranking.

Every figure the finder uses is a typical value from our own material guides: the gasket material chart for gaskets and seals, the types of shims and washers and spacers guides for shims, and the electrical insulation materials guide for insulators.

A material is ruled out when your temperature is outside its typical range, when it is rated poor in something your part meets, or when it cannot do something you need, such as insulate or carry a flame rating. It is flagged, not ruled out, when it is close to a limit, rated fair, not rated at all, or available on request. Each answer says which.

Gasket material chart

What each answer does

Typical values, not a specification

Temperature
Your range is outside its typical service range
Flags it when: Within 15°C of its upper limit (oil, steam and chemicals bring the limit down), or the limit is by grade
What it meets
It is rated poor or not recommended
Flags it when: It is rated fair, or not rated in our guides
Pressure (gaskets)
The duty is above the material's band
Flags it when: A harder material on a light duty, or a grade needed for higher pressure
Food contact
No food-contact grade in our guides
Flags it when: Food-contact grades exist, to confirm with their declaration
Insulating, flame rating
Metal, or no flame rating
Flags it when: Flame-retardant grades on request
Thickness (shims, insulators)
Outside the thicknesses we supply
Flags it when: Thicknesses on request

Common jobs start from the first choice and alternative in our quick picks.

Common questions

The material finder, answered.

Ask our team
Can I rely on the finder's answer?

Use it to narrow the choice. It compares typical values for common grades, as our material guides do, and real limits depend on the compound, the fluid and its concentration, the temperature and how the part is fitted. Ask for a quote from any result and our technical team will confirm the grade for your duty.

Why has a material been ruled out?

Open "Ruled out, and why" under the list: each material shows the reason, such as a temperature beyond its typical range or a poor rating in something your part meets. Change an answer and it may come back.

What does "Check with us" mean?

The material may suit your part, but something needs confirming first: it is close to a limit, rated fair or not rated for something your part meets, or it needs a particular grade. Our team will tell you whether it works.

Do you supply every material in the finder?

Every material in the finder comes from our material guides. Those marked "On request" are supplied to order rather than held in stock; ask us about lead times.

Can I share my answers?

Yes. The page address keeps your answers, and Share copies a link to them. Copy puts the shortlist, with its reasons, on your clipboard.

What if nothing matches?

Send us the conditions with Ask our team. Our guides cover the common grades, and we work with many more, including filled, reinforced and specialist compounds.

Want us to check your choice?

Send us the temperature, what the part meets and the pressure, and our technical team will confirm the material and quote for the part.