Mylar®, Melinex® and Hostaphan® are brand names for the same material: biaxially oriented polyester film, also called PET or BOPET film. Mylar® and Melinex® are made by Mylar Specialty Films, the company known until 2024 as DuPont Teijin Films. Hostaphan® is made by Mitsubishi Polyester Film. Each brand covers dozens of grades, and a grade name tells you who made the film and which product it is, not what it is.
That matters when a drawing or a specification names a brand you cannot get, or when you want a second source. You cannot swap a Mylar grade for a Hostaphan grade by name. You can specify an equivalent by describing what the film has to do, comparing data sheets on the same basis and trialling samples. This guide explains how.
Mylar, Melinex and Hostaphan at a glance
| Brand | Made by | Where it began | Example grades and what they are |
|---|---|---|---|
| Mylar® | Mylar Specialty Films | DuPont, USA, in the 1950s | Mylar® A: a tough, general-purpose film, translucent from 50 to 125 microns |
| Melinex® | Mylar Specialty Films | ICI, UK | Melinex® 339: opaque, glossy pearly white, pretreated on both sides. Melinex® 401: high clarity, with a slip treatment on one side |
| Hostaphan® | Mitsubishi Polyester Film | Wiesbaden, Germany, in 1955 | Hostaphan® RN: transparent and glossy. Hostaphan® WN: translucent white |
| Lumirror® | Toray | Japan | A further major brand you will meet on specifications |
The example grades are not equivalents of each other: they show how differently the makers name their products. Descriptions are from the manufacturers' own literature.
What is Mylar?
Mylar® is DuPont's brand of polyester film, introduced in the 1950s as the first biaxially oriented PET film. The polymer itself was discovered in Lancashire in 1941, and DuPont took the American rights. Mylar® is still made today by Mylar Specialty Films, a joint venture of Celanese and Teijin, which took the brand's name as its own in 2024.
The word has also become a generic name. Metallised balloons, emergency blankets and food storage bags are often called "mylar" whoever made the film, and some of them are not polyester at all. If a specification or a customer says "mylar", it usually means polyester film in general; ask whether a particular grade is required before you assume it is.
What is Melinex?
Melinex® is the British polyester film brand, developed by ICI, which held the rights to the polymer outside the United States. ICI's Melinex® business passed to DuPont in the late 1990s, and in 2000 DuPont and Teijin combined their polyester films in a joint venture, DuPont Teijin Films. Melinex® and Mylar® are now made by the same company, Mylar Specialty Films, but they remain separate brands with their own grade ranges.
In UK archives and libraries, "Melinex" is often used the way "mylar" is elsewhere, to mean any clear polyester film used for sleeves and encapsulation. Our guide to archival polyester film explains what makes a film suitable for long-term storage.
What is Hostaphan?
Hostaphan® is the German polyester film brand. Its first pilot line ran in Wiesbaden in 1955, under the Hoechst group, and commercial production followed in 1957. Mitsubishi took over Hoechst's share of the business in 1998, and Hostaphan® is now made by Mitsubishi Polyester Film, which still makes it in Wiesbaden. Its general-purpose films include Hostaphan® RN, a transparent, glossy film made in a wide range of thicknesses, and Hostaphan® WN, a translucent white.
Is Mylar the same as Melinex or Hostaphan?
The polymer is the same, so the basic properties are similar: a density of about 1.4 g/cm³, high tensile strength, good dimensional stability, good electrical insulation and a useful working temperature range. What differs is everything added to that polymer: slip additives and fillers, pigments, surface treatments and coatings, how the film is stretched and heat set, the thicknesses made and the approvals held.
So the useful question is not whether one brand equals another. It is whether a particular grade does what your job needs. Two grades from the same maker can differ more than two general-purpose grades from different makers.
Why data sheets are not directly comparable
Lining up two data sheets is the obvious first step, but the numbers often do not mean the same thing:
- Typical or guaranteed: some data sheets give typical values, others give minimum or maximum values that every roll must meet. A typical tensile strength looks higher than a guaranteed minimum for the same film.
- Different test methods: tensile strength may be measured to ASTM D882 or ISO 527, and shrinkage to ASTM D1204 or DIN 40634, at different temperatures and times. For example, the Mylar® A data sheet gives shrinkage as a typical value at 150°C for 30 minutes, while the Hostaphan® RN data sheet gives a maximum to a DIN method.
- Different thicknesses: many properties change with thickness, so compare values at the thickness you will buy.
- Different units: dielectric strength may be in kV or kV/mm, thickness in microns, gauge or mil. Our polyester film thickness guide converts between them.
Compare like with like, and where the methods differ, ask the supplier for values to your method or test both films yourself.
How to specify an equivalent polyester film: the properties that matter
An equivalent is a film that matches your current grade on the properties your process and product depend on, and is free to differ on the rest. These are the properties to check, and how each is usually measured.
| Property | Why it matters | Usually stated as |
|---|---|---|
| Thickness and tolerance | Stiffness, insulation, fit in an assembly | Microns, with a tolerance |
| Finish and haze | Appearance, see-through, print contrast | Clear, hazy, matt, white, black or metallised; haze in % (ASTM D1003) |
| Surface treatment | Adhesion of inks, coatings and adhesives | Untreated, corona or chemically treated; one side or both; for solvent or water-based systems |
| Slip and friction | Winding, sheet feeding, handling | Coefficient of friction (ASTM D1894) |
| Tensile strength and elongation | Strength in converting and in use | MPa and %, machine and transverse direction (ASTM D882 or ISO 527) |
| Shrinkage | Dimensional stability through heat, printing and lamination | % at a stated temperature and time (ASTM D1204, for example 150°C for 30 minutes) |
| Dielectric strength | Electrical insulation | kV or kV/mm (ASTM D149 or IEC 60243) |
| Flammability | Electrical and transport approvals | A UL 94 rating, such as VTM-0 |
| Food contact | Packaging and food equipment | A declaration of compliance, for example to EU Regulation 10/2011 |
| Archival quality | Storing documents and photographs | Uncoated, untreated film passing the Photographic Activity Test (ISO 18916) |
| Format | Fit on your machines | Reel width, core size and length, or sheet size |
Not every property applies to every job. A carton window needs clarity, a heat-sealing or print treatment and the right format; an insulator needs thickness, dielectric strength and a flammability rating. Our guides to polyester film grades and polyester film finishes explain the options.
Five steps to approve an equivalent grade
- Gather what you have: the grade name, its current data sheet, a sample, and the drawing or specification it appears on.
- Decide what matters: list the properties the film needs for your process and product, with the limits you can accept. Everything else is free to change.
- Shortlist and compare: choose candidate grades and compare them on the same basis: the same thickness, the same test methods, typical against typical or minimum against minimum.
- Trial samples: run samples through your own process, from printing or laminating to cutting and assembly, ideally from more than one batch. A film that matches on paper can still behave differently on your line.
- Approve and record: write the approved grade into your specification, and tell your own customers if your agreements require notice of a material change, as aerospace, medical and automotive customers often do.
Writing a polyester film specification that survives a change of supplier
A specification that names only one grade leaves no room when that grade is unavailable. One written around properties, with a reference grade, keeps your options open without losing control. For example:
- Biaxially oriented polyester (PET) film, 75 microns;
- optically clear, adhesion pretreated on both sides;
- shrinkage limit stated with its test method and conditions (for example ASTM D1204, 150°C, 30 minutes);
- supplied as sheets cut to size;
- reference grade Melinex® 506, or an approved equivalent.
"Or an approved equivalent" is the important phrase: it lets a supplier offer another grade, but only one you have trialled and approved.
Common mistakes when switching film grades
- Comparing a typical value with a guaranteed one, and concluding that one film is weaker.
- Missing the treated side. A film treated on one side prints on that side only; check which side, and whether you need both.
- Rounding the thickness. 23 and 25 microns, or 36 and 38 microns, are different products, and the difference shows in stiffness and yield.
- Forgetting approvals. A UL listing or a food contact declaration belongs to a specific grade, not to polyester film in general.
- Trialling one roll. Batches vary within their tolerances; trial enough material to see that.
- Ignoring the format. A different core size or reel length can stop a line as surely as the wrong film.
Finding an equivalent with PSG
As an independent supplier and converter, PSG is not tied to any one film manufacturer. Tell us the grade on your specification and how you use the film, and we will supply that grade where it is available to us, or recommend an equivalent and send a data sheet and samples, so you can approve it before you switch. We also make our own Polymex® polyester film, from 12 to 350 microns, with its data sheet published on our grades page.
We supply the film the way your line needs it: as slit reels, as sheets or as parts cut to drawing, through our polyester film slitting and sheeting service, with no minimum order unless a specialist range's maker sets one. For an overview of everything we do with PET, see our guide to polyester film, and for insulation grades, polyester film for electrical insulation.
Need an equivalent for a Mylar®, Melinex® or Hostaphan® grade? Send us the grade name or data sheet and tell us what the film does. Our technical team will recommend a grade and arrange samples for your trial.
Mylar® and Melinex® are registered trademarks of Mylar Specialty Films U.S. Limited Partnership. Hostaphan® is a registered trademark of Mitsubishi Polyester Film. Lumirror® is a trademark of Toray Industries. Polymex® is a trademark of PSG.




